Installation and acceptance of Roots blower → check the wiring of Roots blower starting cabinet and switch the change-over switch to manual gear → open the outlet pipe valve of Roots blower → jog the Roots blower to check the direction of the blower → start the Roots blower → check the operation of the blower → check the air outlet of the air duct (observe the backwash air outlet) → Check the pressure change of the outlet pipe pressure transmitter and the mechanical pressure gauge → stop → switch the switch of the fan starting cabinet to automatic → start/stop the Roots blower at the PLC panel or the central control room operation station → switch the switch of the field control cabinet to the stop position → start/stop the blower should be invalid

（1）風機試運轉前，應符合下列要求：

(1) Before the fan test run, the following requirements shall be met:

1）軸承箱和油箱應經清洗潔凈,、檢查合格后,，加注潤滑油；加注潤滑油的規格,、數量應符合隨機技術文件的規定,；

1) The bearing box and oil tank shall be cleaned and checked to be qualified before lubricating oil is added; The specification and quantity of lubricating oil shall comply with the provisions of the accompanying technical documents;

2）電動機、汽輪機和尾氣透平機等驅動機器的轉向應符合隨機技術文件的要求,；

2) The steering of drive machines such as motors, steam turbines and tail gas turbines shall meet the requirements of the accompanying technical documents;

3）盤動風機轉子,，不得有摩擦和碰刮；

3) Turn the fan rotor without friction and scratch;

4）潤滑系統和液壓控制系統工作應正常,；

4) The lubrication system and hydraulic control system shall work normally;

污水處理羅茨風機

Roots blower for sewage treatment

5）風機的和連鎖報警與停機控制系統應經模擬試驗,，并應符合下列要求：

5) The safety and interlock alarm and shutdown control system of the fan shall undergo simulation test and meet the following requirements:

a）冷卻系統壓力不應低于規定的值；

a) The cooling system pressure shall not be lower than the specified minimum value;

b）潤滑油的油位和壓力不應低于規定的值,；

b) The oil level and pressure of lubricating oil shall not be lower than the specified minimum value;

c）軸承的溫度和溫升不應高于規定的值,；

c) The temperature and temperature rise of the bearing shall not be higher than the specified maximum value;

d）軸承的振動速度有效值或峰-峰值不應超過規定值；

d) The effective value or peak-to-peak value of bearing vibration speed shall not exceed the specified value;

e）喘振報警和氣體釋放裝置應靈敏,、正確,、可靠；

e) The surge alarm and gas release device shall be sensitive, correct and reliable;

f）風機運轉速度不應超過規定的速度,。

f) The operating speed of the fan shall not exceed the specified maximum speed.

6）機組各輔助設備應按隨機技術文件的規定進行單機試運轉,，且應合格；

6) Each auxiliary equipment of the unit shall be subject to single unit test run according to the provisions of the accompanying technical documents and shall be qualified;

7）風機傳動裝置的外露部分,、直接連通大氣的進口,，其防護罩（網）應安裝完畢；

7) The protective cover (net) of the exposed part of the fan transmission device and the inlet directly connected to the atmosphere shall be installed;

8）主機的進氣管和與其連接的有關設備應清掃潔凈,。

8) The intake pipe of the main engine and related equipment connected to it shall be cleaned.

本文由浙江污水處理羅茨風機整理發布,，您是不是對這些內容有所了解了呢?更多的內容請點擊：http://ailelejlb.com 我們會有更多精彩內容等你查看。

This article is published by Roots blower for sewage treatment in Zhejiang Province. Do you know something about these contents? For more information, please click: http://ailelejlb.com We will have more wonderful content waiting for you to check.